Sources / LBL Practical Flex Circuit Design Guidelines / Practical Design Guidelines for Flex

Practical Design Guidelines for Flex

Content

Practical Design Guidelines for Flex

INTRODUCTION

Flexible circuits are obviously unique among electronic packaging technologies in that they off er a wide variety of advantages unobtainable using conventional rigid interconnection technologies. Freeform integration of electronic elements through all three dimensions of space is highly liberating to the design process.

Such advantages, however, cannot be garnered without a thorough understanding of basic fl ex circuit design principles. Proper use of those design principles can provide a path to early success. In contrast, failure to use good design practices can result in early failure. Th e objective of this chapter is to provide information vital to the successful production of fl exible circuit designs-ones that will consistently perform to user expectations.

DESIGN PRELIMINARIES

Before embarking on a fl ex circuit design, it is important that a holistic overview of the project be taken. In this overview, a circuit designer should attempt to take into account as many of the items discussed in the implementation section as are possible or relevant. Th is act of taking stock of the project will help the designer appreciate the broader perspective of the task, minimizing the possibility that a gross and avoidable error will be carried through the design process.

It is also important that the designer keep in mind that fl exible circuit designs require a balancing of both mechanical and electrical concerns. Th ese two competing concerns, the designer will fi nd, oft en oppose each other's requirements in a design. It will be the holistic approach that will help the designer thread the needle to make the best possible choice from given alternatives.

USE OF MOCKUPS

Let us reassert here the value of using paper doll mockups. Th is simple practice will help the designer prevent many errors by exposing potential

problems early and will save both time and money.

Some modern CAD systems have demonstrated the ability to execute three dimensional layouts required for fl ex circuit applications, but the physical model will probably always prove of some value in addressing both the ergonomic elements of assembly and the concerns of access should fi eld repair be required.

DESIGN WITH A BIAS FOR COPPER

Favoring the use of copper in design is good practice for some very solid reasons, assuming that there are not important confl icts created by the practice. If all other design objectives are met, then the primary reason for maintaining extra copper is that it helps to enhance the dimensional stability of the circuit. Designing with a bias for copper is a practice especially well suited to single-layer fl ex circuit designs. See Figure 5-1.

As indicated before, the decision to add or leave copper should be

Figure 5-2 Copper foil is maintained by design around circuits to provide better panel dimensional stability. Two examples are shown.

made in light of the objectives of the circuit's fi nal use. For example, if a reduction in weight of the fi nal product is a key objective, then there would be need to trade away some of the enhanced dimensional stability. Another reason for maintaining the copper is that it reduces the amount of copper etched and is thus more environmentally friendly in terms of chemical usage.

TOLERANCE SETTING FLEX CIRCUIT DESIGNS

Proper application of tolerances of fl ex circuit design features is a matter that concerns both the fl ex circuit manufacturer and the fl ex circuit user.

In general, it is recommended that the largest practical tolerance be given

to all features and locations to facilitate manufacture. Th is is because the base materials are fl exible and prone to distortion, making accurate measurement over distances diffi cult. To compensate, it is recommended that more than one datum be used on larger circuits. Individual datums

Figure 5-3 The use of multiple datums, with one being the prime and the others secondary, facilitates both accurate measurement of the circuit and device placement during the assembly process.

can be provided locally relative to features deemed important. (See Figure 5-3.) Th is will result in a more accurate measurement being taken and can preempt potential confl icts in measurement results between inspectors. To avoid confusion in design, one datum should be defi ned as the primary or master datum and others as secondary or slave datums.

Tight tolerances can be attained, when required, but to do so requires

*Mil-Std-2118 off ers the following statement regarding tolerances: 'Drawing tolerances must refl ect bend and fold allowances between component mounting rigid areas.'

Table 5-1 Tolerance guidelines for standard fl ex circuit manufacture. (Chart does not apply to leading edge products.)

special attention and good techniques. As a result, the expense of tighter tolerance circuits tends to be greater due to anticipated loss of yield. Table 5-1 provides some general guidelines for tolerancing based on diff erent design standards.

Th e values off ered in Table 5-1 are rather generous by today's standards, however. To provide a global perspective on fl ex circuit feature capability, a 2004 survey of 20 Japanese fl exible circuit manufacturers indicated that more than half of the companies were routinely producing fl ex circuits with traces of 110µm or less, and fi ve companies were producing circuits with features of 70-90µm routinely. Today are a number of fl ex circuit manufacturers in Japan and elsewhere are producing circuits having features of 35 to 50µm and some have shown capabilities down to 25µm and even 10µm feature sizes.

GENERAL GUIDELINES FOR DIMENSIONING AND TOLERANCING

Proper dimensioning and tolerancing of fl ex circuits is vital to achieving good manufacturing yield. While it is not possible to point out every possible situation where dimensions and tolerances can be used in such a way as to confuse the interpretation of a drawing, there are certain general guidelines that, if followed, can do much to minimize the potential for confusion. Following are a few such guidelines:

·Show suffi cient dimensions so that the intended sizes and shapes can be determined without requiring the distances between features to be calculated (or assumed).
·Provide individual dimensions only once and check them.
·State all dimensions clearly so they can only have a single possible interpretation.
·Show the dimensions between points, lines or surfaces, which have a necessary and specifi c relation to each other or which control the location of other components or mating parts.
·Check dimensions to avoid accumulations of tolerances that may permit alternative interpretations.
·Provide dimensions to features, which are shown in profi le making certain that the feature's dimensions are not ambiguous.
·Do not show dimensions to lines representing hidden surfaces.
·Do not use 'off part' datums.

SPECIAL DESIGN CONSIDERATIONS

Th ere are some unique elements of fl ex circuit design that require early consideration. Mostly they address mechanical issues that could aff ect usability and/or long term performance. However, they will defi nitely aff ect circuit layout and so are given early consideration.

LAY OUT CIRCUIT TO CONSERVE MATERIAL

Conservation of material in fl exible circuit manufacture serves to help keep manufacturing costs down. Th is is important because fl exible circuit materials tend to be expensive in comparison with standard rigid materials such as FR-4.

We suggest accomplishing close spacing of the circuit. Th e technique of optimizing the number of circuits per panel is called nesting . Th e term optimizing is used in place of the seemingly more logical term maximizing for a reason, that reason being that the layout of a fl ex circuit should be based on end use, and some uses may demand that portions of the fl ex circuit be properly oriented relative to the grain direction of the foil (such as is required for dynamic fl exing). Th is may result in a less-than-maximum material use for circuit construction. However, when this is not the case, there is the opportunity to lay the circuit out in various ways to get the most out of the material.

Figure 5-4 Proper circuit nesting can greatly improve panel yield and lower overall cost. If folding can be tolerated as an assembly operation, yield can be maximized. For dynamic fl ex circuit designs, the grain direction requirement may impact layout.

While nesting is routinely performed by the manufacturer, the designer can aid in this process by taking advantage of the fact that fl ex circuits can be bent and folded. Th us, adding a small length to a circuit arm can allow a circuit to be produced more economically, provided the user doesn't mind adding a folding operation to his assembly process. (See Figure 5-4.)

SERVICE LOOPS

Th e addition of a small amount of length to the fl ex circuit beyond the design requirement is advisable for most fl ex circuit applications. Th is little extra length of material is commonly referred to as the service loop length.

Th e purpose of the service loop is off er suffi cient length to facilitate both assembly of the product and servicing of the product once in the fi eld, if it should ever be required. Th e extra length also helps to compensate for small, unforeseen variations in both the package and the fl ex circuit.

Figure 5-5 Staggered length designs facilitate bending of the fl ex circuit; the circuit can only be bent in one direction by design.

STAGGERED LENGTH CIRCUITS (BOOKBINDER CONSTRUCTION)

For ease of fl exing multilayer and rigid fl ex designs, the use of staggered length design is commonly employed. Th e technique is accomplished by adding slightly to the length of each succeeding fl ex layer, moving away from the bend radius. (See Figure 5-5.)

Figure 5-6 Without staggered lengths, layer buckling occurs.

CONDUCTOR SIZING AND ROUTING

In general, fl ex circuit conductor width and thickness are determined by a combination of current carrying requirements, the voltage drop allowance and/or characteristic impedance control needs. When designing fl ex circuits for dynamic applications, the use of the thinnest possible copper is recommended. Th us, it is important that the designer opt for wider rather than thicker traces to accommodate basic electrical needs or requirements. Th is practice assures maximum circuit fl exibility.

Table 5-2 can be used to determine maximum current and line resistance for given trace widths with both 35µm (1-oz) and 70µm (2-oz)

A common rule of thumb is to add length equal to roughly 1.5 times the individual layer thickness. Th is helps defeat whatever tensor strain might have otherwise been built up in the outer metal layers of the multilayer fl ex and prevents buckling of the center of bend layers (see Figure 5-6).

copper. Th ese are relatively common foil thicknesses used in much fl ex circuit manufacture, although 18µm (½-oz) and even lower copper foil thicknesses are becoming increasingly important.

A number of diff erent nomographs for determining other electrical values for copper have been developed to simplify copper trace-requirement specifi cation. Th e IPC's fl ex circuit design specifi cation is a good source for such nomographs for those who have interest. Th ere is an eff ort underway to revise these graphs, which have long been in use, to refl ect more practical values.

Table 5-2 Current Carrying Capacity of Conductors. Conductor width and copper thickness have a direct impact on the current carrying capacity of a fl exible circuit. The above table provides a means of determining the conductor width for a 10° C rise

| Conductor Width | MaximumCurrent for 10° C rise 1 oz copper | Conductor Resistance milliohms/ft 1 oz copper | MaximumCurrent for 10° C rise 2 oz copper | Conductor Rresistance milliohms/ft 2 oz copper | |-------------------|---------------------------------------------|-------------------------------------------------|---------------------------------------------|--------------------------------------------------| | 0.005 | 0.25 | 1280 | NA | NA | | 0.01 | 0.6 | 640 | 1.0 | 320 | | 0.015 | 1.1 | 400 | 1.8 | 200 | | 0.02 | 1.3 | 320 | 2.0 | 160 | | 0.025 | 1.5 | 250 | 2.5 | 125 | | 0.03 | 1.8 | 200 | 2.9 | 100 | | 0.05 | 2.5 | 120 | 4.0 | 60 | | 0.07 | 3.2 | 90 | 5.0 | 45 | | 0.1 | 4 | 60 | 6.9 | 30 | | 0.15 | 5.9 | 40 | 9.8 | 20 | | 0.2 | 6.9 | 30 | 12.0 | 15 | | 0.25 | 8.6 | 25 | 13.5 | 12.5 |

Trace Width Minimums

Th e minimum practical trace width for a fl ex circuit varies from vendor to vendor. Flex circuits with traces 250µm (0.010") and greater are fairly easy to obtain; however, line widths 125µm (0.005") and lower are increasingly common. Flex circuits having features in the range of 50µm (0.002") and lower are available in volume production from a limited number of vendors, but the number of such vendors is growing to keep pace with the demand for ever smaller electronic products.

Th e type of technology used in circuit feature manufacture also heavily infl uences trace width minimums. For example, plated up copper sputtered polyimide base circuits are basically limited in feature size only by the

photolithographic capabilities of the manufacturer. Th us, very small circuit features can be made. For etched circuit traces, however, the trace width and pitch are infl uenced primarily by the thickness of the base copper foil.

Typically, the trace pitch limit is nearly linear with copper thickness within a narrow range. 18µm (½-oz) copper will yield circuit features at a 125µm (0.005") pitch, while with 35µm (1-oz) copper, etching becomes more diffi cult under 175µm (0.007") pitch. While some manufacturers can successfully produce 25µm (0.001") features with 18µm copper, vendor capabilities vary widely. It is best to check with the fabricator before attempting to design very fi ne line features.

CONTROLLED IMPEDANCE LINES

Controlled impedance transmission cabling is a popular application for fl ex circuits, and the value of such product is increasing as digital data signaling speeds continue to rise.

Tighter tolerances for etched features are possible with fl ex circuits because of the lower profi le adhesion treatment or 'tooth' of the copper. Th e use of thicker fl exible dielectric substrates, if the design allows, can ease somewhat the etching challenge because thicker substrates allow for wider signal lines, which can be fabricated more easily to meet the tight tolerances needed for controlled impedance circuits. Th is topic will be discussed in more detail later in this chapter.

ETCH FACTORS

An etch factor is a tool used by the manufacturer to compensate for isotropic etching process eff ects. It is recommended that the designer check with the vendor to determine if they want inclusion of an etch factor. Usually it is best if the manufacturer makes this adjustment, as they will be most familiar with their process and its capability.

Figure 5-7 The etching process works laterally as well as down, at a ratio of roughly 1:2 laterally to down

Th e typical line width loss (measured at the top of the trace) due to the etching process is approximately 2x copper foil thickness, although copper type, conductor pitch, etch mask, process chemistry and equipment can all infl uence the results.

CONDUCTOR ROUTING CONCERNS

Th ere are a few general issues related to conductor routing of a fl ex circuit. Th e fi rst item of concern is keeping to a minimum the number of crossovers in the layout. Th is will help to keep the layer count down and lower the cost. Newer CAD systems can respond to such a requirement, but the results may need to be massaged or optimized to make certain that the smallest possible area has been consumed in the process.

Routing of conductors on a fl exible circuit perpendicular to bend and fold is the recommended design practice. Th e purpose is to facilitate the bending or folding process and to minimize stress through the area. In addition, circuitry should be routed on a single copper layer through bend and fold areas whenever possible.

Figure 5-8 Routing options for fl ex circuit trace corners. Avoid sharp corners if possible. A radius is best as it provides a smooth transition and mitigates potential issues related to stress risers.

It is also recommended that designs avoid having right or acute angles (≤ 90°) in circuit routing. Th is is because they tend to trap solution and may over etch in process. Th ey are also more diffi cult to clean aft er processing, so best practice dictates that corners should be provided with a radius if possible. Th e radius also improves signal propagation, as the refl ections at turns are reduced.

With double-sided fl ex, when and where the conductors must be routed through bend and fold areas and when copper traces are on both sides, the circuit designer should design spaces to be approximately 2-2.5x the trace width.

Preferably, the designer should also stagger traces from side to side. Th e purpose of this practice is to avoid the I-beam eff ect. Th is can be a critical concern in dynamic applications. (See Figure 5-9.)

Flexible Circuit Technology

Figure 5-9 I-Beamed vs. Staggered Conductors. I-beamed constructions increase the stiff ness of the circuit through bend and fold areas. A better alternative, if space allows, is to stagger conductors for improved fl exibility.

Finally, placement of vias within the bend area is highly discouraged as they will adversely aff ect bend formation and create unwanted points of stress and potential crack propagation.

GROUND PLANE DESIGN

Ground areas should be crosshatched if electrical consideration of the design will allow for such. Th e practice helps both to reduce weight and improve circuit fl exibility. Th e size of the openings in the ground plane may be critical depending on the end product requirements for shielding or controlling of characteristic impedance. If openings are too large, some shielding eff ects may be lost, depending on frequency. Also, ground connections for components should be thermally relieved to reduce heat sinking and assure formation of a good solder joint. Th is is accomplished by etching a clearance area around the pad while maintaining electrical connection. Figure 5-10 illustrates the technique.

Figure 5-10 Ground planes should be crosshatched if possible to improve fl exibility. Clearance holes prevent shorting. Ground connections should be relieved to reduce heat sinking when soldering.

POLYMER THICK FILM DESIGN GUIDELINES

Due to their unique nature, polymer thick fi lm (PTF) circuits have their own very specifi c design rules. As a screen printing based technology, the limits of design are tied to two main factors: (1) the conductivity of the ink chosen and the limits of the screen-printing materials, and (2) the processes used. Much of the latter factor is tied to the former. Th at is, the particle size of the included conductor material and the polymer carrier will help establish the limits of screen printing. Emerging nanoparticle technologies could boost conductivity signifi cantly, possibly opening the door for broader use of polymer thick fi lm technology. While PTF circuits are not generally considered for dynamic applications, they can actually perform quite well in certain dynamic applications. Some experimenters have reported increases in conductivity with cycling. PTF membrane switches also stand as witnesses to the effi cacy of PTF as a fl exing technology.

CONDUCTOR WIDTH AND SPACING FOR PTF

Generally, minimum conductor width and spacing is considered to be in the range of 375µm (0.015"). It is possible to produce fi ner lines and spaces using PTF inks, but conductivity can become more of a design performance concern.

CURRENT CARRYING CAPACITY OF PTF

Silver-based polymer thick fi lm inks, under normal conditions, can be expected to carry approximately 25% of the current of copper circuits for equivalent line widths and nominal PTF ink thickness. Care should be used, however, in attempting to maximize conductor current-carrying capability under this premise. Hot spots within the conductor matrix can cause rapid degradation of the conductor and possible failure.

SCREEN-PRINTED PTF RESISTORS

Screen-printed resistors are fairly commonly incorporated into PTF circuit designs. If used in a design, the resistors should be kept to a minimum of one or two values to facilitate processing. Generally, the resistors can be printed to ± 20% of value without trimming. Laser or mechanical trimming of the resistor can be used if tighter tolerances are required.

TERMINATION DESIGN CONCERNS FOR PTF CIRCUITS

Th e design rules for circuit pads or lands for PTF circuits are similar to those used for rigid printed wiring boards; however, the termination features should be discussed with the manufacturer. While polymer thick fi lm inks are not directly solderable, conductive adhesives can be used to surface mount components. Again, land design for surface mounting is similar to PCBs.

INTERCONNECTION DESIGN FEATURES

Th is chapter section deals with interconnection design features, including both through holes and lands for making interconnections and the design criteria for making those access points more reliable.

HOLE SIZES FOR COMPONENT LEADS

While surface mount technology has become the dominant interconnection technology for electronic component assembly, through hole components are still used in many applications. As a result, proper sizing of the hole remains an important design checkpoint.

Finished hole diameter for through hole mounted components in fl ex circuits for most applications should be nominally 200-250µm (0.008-0.010") larger than component lead to meet best practice design requirements for automated component placement. However, this is not always possible or practical. One key advantage of fl ex circuits is that, because of the thinness of the circuit, smaller gaps between the component and the through hole can be reliably soldered-but the devices are more diffi cult to insert.

Best or preferred case fl ex design practice suggests that all lands or pads should be made 2-2.5x the hole diameter. Holding this value is primarily a concern with single-sided fl ex, where maximum solderable area is sought to ensure that a reliable connection can be made.

Again, as with drilled through holes, this ratio will not always be practical, as is the case with miniature connectors. In those cases where very small lands are mandated and pin in hole assembly is required, a plated through hole may be required to enhance solder joint reliability.

Figure 5-11 Through Hole Land or Pad Termination Sizing. Maintaining a proper drilled hole to pad relationship is most important with single layer fl ex designs. Plated through holes can get by with smaller lands.

VIA HOLE SIZING

Vias can be designed as small as is practical for the manufacturer's yield. Small vias off er great advantage for circuit layout, but circuit cost may be aff ected if they are designed too small, depending on what technologies are available for making holes in the base material. Current generation punching and laser techniques are capable of economically mass producing interconnection vias as small as 25-50µm (0.001-0.002'). In contrast, drilling, because of the higher cost of small drills, becomes more expensive

as the holes get smaller. Because fl exible circuit base materials are thin, it is fairly easy to plate small through holes reliably. Th e small plated holes are also highly reliable in fl ex circuits. Th is is due in large part to the thinness of the base material, which results in a total material expansion that is low and less of a concern with respect to thermal cycling.

Figure 5-12 The practice of fi lleting pads helps to improve the reliability of the circuit by more evenly distributing stresses at the junction of the circuit land to the coverlayer opening.

FILLETING OF LANDS AND PADS

Termination lands and pads on fl exible circuits should be fi lleted. Th is process increases pad area and helps to distribute stresses local to the coverlayer openings better, eff ectively relieving a stress riser condition that commonly causes failure if the fi llet is not supplied or ignored. Earlier CAD systems had diffi culty in producing these features, but today's more advanced systems can more reliably address the requirement for fi llets without diffi culty. See Figure 5-12.

PAD OR LAND HOLD DOWNS FOR SINGLE-SIDED FLEX

Termination pads on single conductor layer circuits and surface mount lands on fl ex circuits of any layer count may require special land hold down techniques. With single-sided fl ex circuits, the use of special features variously referred to as tie down tabs, anchoring spurs, or rabbit ears may be employed to prevent the land from lift ing during soldering processes in cases where excessive heat is used. With new lead-free solders, this may become more important.

An important note on this subject is that features such as tie down tabs could well cause problems as the industry moves to higher data rate signaling, and they should be used with caution. Th e stubs associated with some tie down features are capable of acting like antenna and can broadcast noise within the package when higher frequencies are used. Th us, an evaluation of the approach may be warranted, depending on the nature of the design. Figure 5-13 shows typical hold down tab features and alternative designs.

Figure 5-13 Various pad designs to help facilitate their capture by the coverlayer. (A) Standard fi lleted pad with full pad capture (B) Standard fi lleted pad with hold down tab (C) Overlapping pad design (D) Oval pad design (E) Corner entry to square pad (F) Plated through holes normally require only fi lleting.

SURFACE MOUNTING LANDS FOR FLEX

Surface mount in combination with fl ex circuit technology is now very popular as the world's fl ex circuit designers look to the success of Japanese products, which oft en employ fl ex circuits with surface mounted components. Surface mounting lands, however, oft en require a slight modifi cation of standard design rules when applied to fl ex circuit applications.

Th e use of holes or slots drilled or routed into the coverlayer before lamination is a common way for fl ex circuit manufacturers to access solder lands. However, if traces are routed straight into the land, misregistration of the coverlayer could result in the creation of a stress riser, as shown in Figure 5-12. Th e same concerns regarding through hole components hold true for surface mount land features. In Figure 5-14 (A), the potential stress riser condition is again shown. Side or corner entry to the land is more tolerant to misregistration (Fig 5-14 [B]). Laser-cut or mechanically punched or routed coverlayer openings can be made rectangular (Fig 5-14 [C]).

Potential

Figure 5-14 Coverlayer openings for discrete SMT components create special design concerns.

Figure 5-15 Examples of precisely photoimaged cover fi lms for surface mount lands on fl exible circuits (Photo courtesy DuPont)

Rectangular openings can also be achieved by using photoimageable cover fi lms in place of a coverlayer. When accessing component lands for device assembly, it is recommended that solder lands extend beneath the coverlayer, as shown in Figure 5-15.

SMT device lands for both discrete and leaded devices should be extended to allow capture by the coverlayer. Normally, lands should be 250-375µm (0.010 to 0.015") larger to facilitate land capture and prevent undesired lift ing of the land during assembly or repair.

As with single-sided through hole lands for fl ex circuits, the objective is to prevent land lift during soldering operations and to provide extra strength against component pull-away in operation. Th is is of greater importance with components of greater mass. Figures 5-15 and 5-16 provide examples of common approaches used to access surface mount features in fl exible

Figure 5-16 The coverlayer openings for peripherally leaded SMT lands can be accessed either discretely or in gang fashion, by prerouting or punching the coverlayer before lamination. Use of photoimageable coverfi lms makes this task much easier.

circuit design applications while maintaining hold down capability.

LANDS FOR PLATED THROUGH HOLES

Except for the shared need for fi lleting, double-sided fl ex with plated through holes does not require tie-downs, due to the rivet eff ect from the plated through hole. Th is inherent feature of the plated through hole serves eff ectively in preventing the pad from lift ing away from the surface of the fl exible circuit during soldering processes, should excessive temperatures be used in the assembly operation. Plated through holes are especially advisable if very small pads are required by the design to ensure formation of a reliable solder joint. Th is may require the addition of a second layer of copper, thus making a single-sided design a double-sided one. But, ease of processing and increases in reliability should, hopefully, off set any increases in cost.

BUTTON PLATING

An alternative plated through hole construction can be created using a process called button plating. Th e process can best be characterized as one where through holes and vias are selectively plated with copper. A fi nished structure can be seen in Figure 5-17.

Th e basic idea is relatively simple, however, success requires reasonable care in the manufacturing process. In practice, the manufacturer fi rst drills and makes conductive the hole walls of the fl ex circuit using a suitable technology (electroless copper or graphite coating). Th e manufacturer

Figure 5-17 An example of button plating

next takes the panel in for imaging, where the panel is coated with a photoimageable plating resist, and the holes and vias to be plated are exposed and developed. A copper pattern plating step follows, and the hole walls and annuli of the holes are plated to the specifi ed thickness. Th at resist is stripped away, and a second plating resist is applied and exposed to create a positive circuit image, which can then be etched to create a metal circuit pattern. Th e holes and vias are tented over in this process. Th is action prevents the metal etching chemistry from entering the vias and etching out the holes, thus creating electrical opens.

COVERLAYER AND COVERCOAT CONCERNS

As mentioned earlier in the section on fl ex circuit materials, there are several types of fl exible covercoating systems available. Each has its own special applications and advantages. Included among them are the following:

Adhesive-backed fi lms

Adhesive-backed polymer fi lms are the type of coverlayer most frequently specifi ed and used by fl ex circuit designers and manufacturers. It is also the fl ex circuit covering method best suited to dynamic fl ex circuit applications because of the balanced material properties from side to side.

Screen-printable liquid covercoats

Applied and cured by simple means, screen-printable liquid covercoats are the least expensive covercoat type and the one most oft en used with polymer thick fi lm and simple single-sided copper constructions.

Photoimageable liquid and fi lm polymers

Newer methods for covercoating fl ex circuits involve the use of photoimageable polymers. Th e results have been very promising. In process, the fl ex circuit is coated with a polymer fi lm, which can then be imaged and developed to access termination features. Th is method, which looks quite good for many applications, could help put an end to many of the coverlayer misregistration problems manufacturers have had with small features and, in addition, quell concerns over adhesive squeeze-out onto lands.

In most fl ex circuit designs, the coverlayer or covercoat serves more than one purpose. For example, covercoats commonly function as a solder mask, helping to prevent solder from shorting circuit traces together, and serve to isolate electrically and protect physically the circuit from damage.

In addition, as described earlier, coverlayers serve to help restrain the pads physically and hold them in place during soldering, preventing pad lift . Th e coverlayer (or possibly a covercoat) also allows conductors to be placed in the neutral axis for improved fl ex and bending performance. Th is subject will be covered in more detail later in the chapter.

Given the diversity of the roles fl ex circuits play in electronics packaging, it is understandable that it has been diffi cult for suppliers to come up with a universal solution that is at once low cost, high performing and easy to apply. Nevertheless, steady progress is being made by material suppliers, and new solutions are regularly being developed and off ered to the industry.

SIZING COVERLAYER OPENINGS

As was seen in the discussions on surface mount land design, the sizing of coverlayer openings varies according to pad design features and with the

number of metal layers. Again, the key area of concern is with single-metallayer fl ex circuits, where potential pad lift demands special care in design. Table 5-3 provides general guidelines for sizing of coverlayer openings.

TRACE-TO-CUT LINE CONCERNS

Best current practice for fl ex circuit design generally recommends that the edge of the part to the edge of conductor spacing be >1.25mm (0.050"). It has been shown, however, that circuits can be made reliably with edgeto-conductor spacing of ≤ 250µm (0.010"), although this normally comes at increased cost, which will vary depending on the tooling system used. Refer to Table 5-1 on page 77.

Table 5-3 Coverlayer opening guidelines vary with the nature of the design.

| Flex CircuitType | Coverlayer Opening | |-----------------------------------------------------------------------------------------|---------------------------------------------------------------------------------------------| | Single metal layer flex circuit with land hold down features | Coverlayer opening can be roughly equal to pad diameter. | | Single metal layer flex without land hold down features or filleting | Openings in coverlayer should be 250µm (0.010") less than pad diameter. | | Double-sided flex PCBs and multilayer flex with plated through holes and filleted lands | Coverlayer opening can be equal to or slightly larger than pad. This minimizes squeeze out. | | Non-component plated through hole vias | No opening unless needed for electrical test purposes |

TEAR-RESISTANCE FEATURES IN FLEX DESIGN

All fl ex circuit designs should be made as tear-resistant as possible. While the material may not be intrinsically tear-resistant, tear-resistance can be improved by employing certain features in the design. Th ere are several possible methods, described below and illustrated in Figure 5-18.

All of the following techniques have been successfully used to help prevent tearing. One or more of the following techniques can be used:

Radius All Internal Corners

Th e fi rst line of defense against tearing is to make certain that all internal corners are provided with as generous a radius as possible. Th is design practice is the most important and simplest of all methods used to prevent tearing of the fl ex circuit material.

Leave Metal in Corners

Th e circuit design should, if possible, have small areas of copper provided for at internal corners to serve as tear stops at the inside of corner radii. Th is serves to prevent further or imminent propagation

of a tear through the polymer, should a tear in the material start.

Laminate Glass Fabric in Corners

Glass cloths can be laminated into corners during the fabrication process. Th ough not fl exible, this method has been shown to provide a very robust corner construction and has been favored in the past by military product designers. It is an expensive solution, however, because of the type of preparation required and should be used only aft er careful consideration of the alternatives. (See Figure 5-19.)

Use Fluoropolymer Coverlayer

Th e use of fl uoroplastics such as Tefl on ® as coverlayers helps to improve tear resistance by virtue of the high tear resistance of the polymer itself. Th is is due to the fact that fl uoropolymer tends to stretch rather than tear, adding toughness to the substrate. An additional benefi t of using fl uoropolymer coverlayers for those involved in high frequency design is that the dielectric constant of the coverlayer is much lower.

Use of Radiused Slots

Th e use of slots with ends that have a radius to access relieved circuit features also can serve to provide tear resistance. Normally, such features can easily be provided for during the punching operation or other circuit fabrication process.

Drilled Holes at Corners or Ends of Slits

Drilled or punched holes in corners or at the ends of access slits have been used with success when fl exible appendages must be spaced close together. Th is method allows the greatest use of material, but the hole size chosen will impact tear resistance. If the hole is very small, the overall robustness will be reduced.

Aramid Fibers Inside Cut Line

As an alternative to glass cloth, the use of aramid fi bers routed through corners or along the entire outline of the fl ex circuit is a unique method to stop tearing of fl ex circuits. Th e thin polymer fi bers have very high strength and are very pliable, minimally aff ecting fl exibility. However, this is a labor intensive method and should only be specifi ed with the knowledge of cost impact.

Ultimately, the choice of which method to use to restrain or prevent tearing of the fl ex circuit is not of overriding importance. What is very important is that the designer makes certain that some suitable method to protect against tearing is used.

To summarize, all internal corners should be provided with radii, and it

Figure 5-18 Tear-resistance features are important. A number of methods for tear restraint work well for fl ex. Shown above are: (1)Large radius in corner (2)Embedded glass cloth (3)Recessed slot (4)Hole in slit (5)Drilled hole at corner (6)Embedded aramid fi ber (7)Extra copper in corner

is here reemphasized that square or sharp internal corners are an invitation to trouble and should be studiously avoided. If the area of the corner is to be permanently bonded to a rigid base, then it is less important but still recommended that a radius be used.

STIFFENERS AND REINFORCEMENTS FOR FLEX

Stiff eners or reinforcements are commonly used to support components

Figure 5-19 Example of circuit with embedded glass-cloth tear restraint

on fl ex circuits. Th ese important 'add-ons' can be fabricated from a wide range of materials, depending on design need. Th e choice of material is predicated on what objectives are sought (low weight, best heat sinking, lowest cost, best spring qualities, etc.). Th e materials referenced in Table 5-4 have all been successfully employed to reinforce fl exible circuits.

In addition to materials mentioned in the table, the package or box

into which the circuit is to be placed can also be used as the stiff ener if the design allows. Beyond simple component support, this technique allows the package or box itself to be used for heat dissipation. While a potentially attractive solution for a number of applications, the diffi culty of this method comes to light if repair is required, because removal can damage the circuit.

Table 5-4 Stiff ener Material Choice for Flex Circuits. A wide range of materials, both conductive and insulating, can be used to provide stiff ness to a fl ex circuit where required. The table above notes some of the materials that have been used for diff erent applications and needs.

| R ESIN - GLASS LAMINATES | E XTRA LAYER OF COVERLAYER | |----------------------------|------------------------------| | T HERMOPLASTIC SHEET | B ERYLLIUM COPPER | | S TAINLESS STEEL | A NODIZED ALUMINUM | | I NJECTION MOLDED BASES | QUARTZ GLASS |

SPECIAL TECHNIQUES FOR STIFFENERS

Special design techniques allow stiff eners to serve more than the function of component support. For example, while the primary purpose is to support components, stiff eners can be so designed as to aid assembly by enabling the fl ex to be assembled as virtually a rigid board. Th is can be accomplished by using one of the following techniques.

ROUT-AND-RETAIN STIFFENERS

Rout-and-retain stiff eners are produced by CNC routing of the substrate so as to leave it attached in certain locations for easy removal later. Such constructions allow the stiff ener to be snapped or cut off aft er assembly. (See Figure 5-20.)

While routers are pervasively used in circuit manufacturing, lasers and water-jet cutters are other potential manufacturing choices for preparing or pre-cutting stiff eners

RETURN TO WEB PUNCHING

Return to web punching (also referred to as 'punch out, punch in') of the stiff ener requires special punch tooling wherein the rigid material is punched out of the panel and then immediately pushed or punched back into its original position in the panel. Th e method is commonly used for inexpensive rigid boards and allows mass assembly with relatively simple assembly fi xture requirements.

SCORING OR DICING OF STIFFENERS

If features of the fl ex circuit design allow the use of scoring or dicing tools to prepare the stiff ener panel is potentially possible. With respect to the scoring process, the circuit and/or the stiff ener is cut partially through, using special tools which cut a controlled-depth straight path through the rigid circuit material. Th e cut can be made through the rigid material alone or through both fl ex circuit and rigid base. Aft er component mounting and assembly, the circuits can be snapped apart along the score lines.

In contrast to the routing concept shown, the other alternativedicing-requires cutting completely through the circuit and stiff ener. Because of the nature of the tools used, all material cuts must be made in a straight line and orthogonal to the major (X&Y) dimensions of the panel.

ADHESIVES FOR BONDING OF STIFFENERS

All of the bonding adhesives used in the creation of fl ex circuit laminates are candidates for attaching a fl ex circuit to a stiff ener. Th e choice of which adhesive to use is most oft en a function of performance requirements.

It is worth checking with the fl ex circuit vendor for his recommendations. Beyond those adhesives used in normal fl ex circuit construction, there are other types of adhesives that can be used as well. Following are some of the more commonly used adhesives for stiff ener attachment.

PRESSURE-SENSITIVE ADHESIVES

Pressure-sensitive adhesives are very commonly used to attach stiff eners. Th ey are perhaps the most versatile and easiest to use. Th ey exhibit very good bond strength, which in some cases actually improves

with age. Th ese adhesives are not generally designed for extended use at high temperatures but are for the most part limited to enduring only short excursions at high temperatures (soldering temperatures). Again, with lead-free solder technology moving ahead, there is need to check capabilities when using higher-temperature lead-free solders.

One particular advantage PSAs off er over other adhesive choices is that, when applied directly to the fl ex circuit, they allow for the fl ex circuit to be bonded to virtually any surface, thus eff ectively making anything in the package a potential stiff ener.

THERMOSETTING ADHESIVE FILMS

Th ermosetting adhesive bonding fi lms (cast-acrylic fi lms or fl ex circuit bondplies) can also be used to bond fl ex circuits to stiff eners, but they require the time and expense of an additional lamination step. Even so, thermosetting fi lm adhesives can off er very high bond strength of the fl ex to the stiff ener.

LIQUID ADHESIVES

One and two part liquid epoxy type adhesives have been used for bonding stiff eners to fl ex circuits. Th ey are diffi cult to apply uniformly and thus do not enjoy wide popularity. Such adhesive materials are well suited for-and can be well applied in-the creation of strain relief at the transition edge of the fl ex and stiff ener by creating a bead of epoxy along the entire edge of the transition.

THERMOPLASTIC ADHESIVE FILMS

Th e use of thermoplastic-based adhesive fi lms for bonding fl ex circuits to stiff eners is another common option. Th ermoplastic fi lms have some unique advantages among adhesives in that they are low-stress, fullypolymerized polymer resins that require no cure. With properties that include adhesion to a wide variety of surfaces and materials, and the reported ability to be reworked easily, these adhesive materials may see expanded service in the future.

UV CURABLE ADHESIVES

Ultraviolet curable adhesives are another potential adhesive choice for stiff ener attachment. With some screen-printable formulations, the UV 'activates' the polymer, creating a tacky adhesive with PSA qualities. In addition, because they can be rapidly cured, these adhesives are also an attractive choice for relieving strain on the fl ex circuit at the transition point from rigid to fl ex.

HOLES FOR STIFFENERS

Th e diameter and relative sizing of mounting holes for components,

of the circuit or breaking of the copper at the transition point can more easily occur if the procedure is omitted from the design or manufacturing process. One or both of the following techniques should be used.

ROUNDED STIFFENER EDGES AT TRANSITION

Th e stiff ener edges in areas where the fl ex circuit egresses from the perimeter of the stiff ener should be rounded or provided with a radius at the edge to prevent a

Figure 5-22 Mounting holes should retain copper when fl ex circuit is to be mounted without mechanical support.

point of focused stress. Alternatively, breaking the rigid stiff ener with a fi le or sandpaper at the transition edge before assembly can provide a similar benefi t.

FILLET TRANSITION EDGE OF STIFFENER

Filleting of the transition edge of a stiff ener with a resilient adhesive or epoxy is another common method of strain relieving circuits. Th e small bead of a suitable polymer will provide a simple means of transitioning strain from the stiff ener to the fl ex circuit. Figure 5-23 illustrates the two approaches.

Figure 5-23 Strain relief at the fl ex to rigid transition helps minimize the potential for focus stress.

STRAIN RELIEF FOR UNSUPPORTED FLEX CIRCUITS

Strain relief should also be provided when mounting the fi nished circuit or assembly. Th e following methods can be used for this purpose:

1. Break or radius sharp edges of any retaining bars or clamps may be used to hold the fl exible circuit in place.

Use a low modulus, elastomeric material between restraining bars and the fl ex circuit.

1. Bond the circuit to the assembly housing, using a double backed adhesive foam material or simple pressure-sensitive adhesive.

and those for fi nal fl ex circuit assembly mounting, have diff erent purposes and oft en somewhat oppositional requirements. Th e result is that the design rules can vary considerably, depending on the application. Explanations as to how to determine the appropriate size follow. Figure 5-21 illustrates the concept.

COMPONENT HOLES IN STIFFENER

Holes in the stiff ener for through hole mounting of electronic components, such as dual in-line packages (DIPS), should be 250µm375µm (0.010-0.015") larger than the through holes in the fl ex circuit (which, in turn, are by design rule 250µm [0.010"] larger than the lead). Th is is to allow for any movement and misregistration between fl ex and stiff ener that might occur during the stiff ener lamination or bonding process. Th is technique also helps to assure the greatest opportunity of accessing the through hole with the component lead without interference from the stiff ener.

Figure 5-21 Access holes through the stiff ener fi ll diff erent needs. Holes in the stiff ener for leaded components are made slightly larger than holes in the fl ex circuit. This allows for any movement during the stiff ener lamination process. It also assures maximum opportunity for accessing the through hole with the component lead.

ASSEMBLY MOUNTING HOLES

Holes in the stiff ener for mounting the assembly should be equal to or slightly smaller in diameter than the holes in the fl ex. Th is assures that the stresses are placed on the rigid portion of the assembly and not on the fl ex circuit. Th is is not an ironclad rule, as it is possible to mount the fl ex circuit directly to a carrier without a stiff ener, using common mounting hardware if necessary.

UNSUPPORTED MOUNTING HOLES

Mounting holes that are not supported by a stiff ener should be designed to maintain copper around the hole for added strength. (See Figure 5-22.) Th is practice is of value with regular mounting holes, as well, if the design will permit. Such features are also a convenient means of making a connection to ground.

STRAIN RELIEF FOR FLEX CIRCUITS

Th e provision of strain relief at the edges of stiff eners helps to prevent stress risers from occurring at transition areas from fl ex to rigid. Tearing

METHODS OF CONNECTING FLEX CIRCUITS

Connecting a fl exible circuit to other elements of an electronic system is a vitally important element in system design, manufacture and assembly. Th ere are numerous methods of making connection to fl exible circuits. Virtually all connector manufacturers have connectors either specially built for, or readily adaptable to, fl ex circuit designs.

Figure 5-24 Patent drawings of a novel high density fl exible circuit based connector invented by John Krumme and Gary Yasumura while they were at Beta Phase. A shape memory alloy was used to open the unique zero insertion force (ZIF) connector.

One innovative connector manufacturer of record, Beta Phase, Inc. (Menlo Park, Calif.), actually made its connectors out of fl exible circuits, producing high-performance connectors with very high pin count equivalents. Th e concept was much ahead of its time and did not get much use outside of extreme performance applications, such as the Cray supercomputer, but the technology was purchased by Molex, and some elements of the earlier concepts are now available. As well, other connector manufacturers now have comparable product in the market.

FLEXIBLE CIRCUIT CONNECTOR TYPES

Some basic connectors are relatively simple devices. Examples include insulation displacement and crimp-type connectors. Th ese have proven popular in applications where cost is important. Th ey are not generally considered suitable for high-reliability applications, however.

To make both male and female pin in socket type connectors, swaged or brazed pins can be attached directly to the fl ex circuits. Th ese have also brought some success in certain low-end product areas where performance is not a key concern.

Th e Sculptured ® fl ex circuit technology described earlier has the ability to integrate the connector directly into the fl ex circuit itself. Th e method is suitable for a number of diff erent electronic applications, due to the fact that no discrete joining of pins to the fl exible circuit is required. By using this technology approach, it is possible to have edge contacts that extend, unsupported, beyond the edge of the fl ex circuit. It is then possible to simply post-form the leads as required to create a viable male pin connector for mating with a compatible socket.

Figure 5-25 Historical approaches for soldering military style two part connectors to fl ex circuits. A key concern is inspection, as solder joints are hidden by each successive layer.

In addition, or as an alternative to the sculpturing method described, edge card contact constructions can be created by folding the contact area of a fl exible circuit around a stiff ener. Th is is a simple and relatively inexpensive way to interconnect a fl ex circuit. It is directly analogous to edge card contacts on rigid boards, for which there are numerous types of mating connector solutions available. Because the fl ex circuit itself is thin, it is possible to accommodate a wide range of connector designs simply by altering the thickness of the stiff ener (see Figure 5-26).

Surface mounted connectors are an increasingly important and common connector choice for use with fl exible circuits, for obvious reasons. With size reduction a common objective

Figure 5-26a Ends of the fl exible circuit can be converted to an edge card contact by placing a stiff ener behind the fl ex and folding and bonding the fl ex to the stiff ener.

of fl exible circuit technologies, it comes without surprise that low-profi le connectors are well-suited to the needs and abilities of fl ex circuits.

A number of low-profi le connectors are presently in the market. Th ese miniature connectors are very nicely suited to many space-constrained fl exible circuit applications. Low-profi le connectors known as lowinsertion-force (LIF) and zero-insertion-force (ZIF) connectors that can handle contact pitches down to 0.30mm (.012") have been produced by commercial manufacturers. Th e profi le height for such connectors can be as low as 0.60mm (.24").

Another option for low profi le interconnection of fl exible circuits is lapped connections. Solder, conductive polymers and adhesives have all

been used to make lapped connections between a fl ex circuit and a mating interconnection structure. It is a reasonably common method; for example, a large percentage of fl at panel displays are connected using anisotropic adhesives.

Another unusual design approach to making fl ex circuit interconnections is one wherein the connections are made directly between chips, using anisotropic adhesives or lap soldered connections. Th is approach has been proven, both by modeling and manufactured prototypes, to be capable of providing very high speed and low power.

To summarize the topic, connecting the fl exible circuit to a next level or associated interconnection device or system can be accomplished using one of many options. Th e choice is predicated on the cost and performance requirements of the end product. Th e examples provided are not exhaustive in terms of options, but they are representative.

BENDING AND FLEXING DESIGN CONCERNS

Figure 5-28 Making fl ex circuit connections directly between chip packages can provide signifi cant performance improvements. (Courtesy SiliconPipe, San Jose, CA)

While fl ex circuits typically are employed simply to allow the user to form the circuit to fi t the shape of the package (fl ex to install applications), there are still many applications that require some dynamic fl exing. In fact, in most applications, the very act of placing the fl ex circuit into the assembly requires that the circuit be bent or folded. In some applications this can occur several times. Flexible circuits are capable of enduring many millions or even billions of fl exural cycles, provided the design is properly matched to the task.

Th ose not involved in dynamic fl ex design should also take to heart the

lessons of this process. For example, it is important to remember that even static fl ex circuits can be dynamically cycled by virtue of their application and design. Such events are common occurrences in circuits designed for any type of mobile equipment, such as automobiles and planes.

For example, shock and vibration encountered by a vehicle can cause a fl ex circuit to endure millions of low amplitude, high frequency fl ex cycles. If dynamic fl ex design rules are not taken into account or are simply ignored, the potential for unexpected cyclic fatigue failure of an application subjected to shock and vibration exists. Attention to the few simple rules for dynamic fl ex provided here can benefi t many fl ex circuit applications. Th ey are, arguably, good practice for all fl ex circuit designs.

BENDING AND FLEXING TECHNIQUES

A number of clever approaches and techniques have been developed by engineers over the years to achieve the desired bending or fl exing motion in a fl exible circuit. Th e types of motions employed range from linear extension and contraction to rotational fl exing through various small angles of 5° or 10° to more than 360°. Figure 5-29 provides conceptual examples.

AVOID PLACEMENT OF THROUGH HOLES IN BEND AREAS

An important design practice that is sometimes overlooked or ignored is the avoidance of placing plated through holes in the bend areas. Th is is of particularly great importance in dynamic applications. For static applications, it may be possible to place vias through a bend successfully if they have a coverlayer and if the bend radius is large enough. Th at said, it is still a practice that should be avoided.

ROUTE TRACES AT 90° THROUGH BEND AND FOLD AREAS

Conductor traces should be routed through bending and fl exing areas at 90° (perpendicular) to the bend line. Th is is an intuitively natural routing scheme and serves the purpose of bending well. However, the rule is somewhat fungible and seems to be violated regularly for matters of convenience. For example, in some hinge circuits (see Figure 5-33), the traces may be bent in more than one direction to achieve the design purpose.

ROUTE CONDUCTORS ON A SINGLE LAYER THROUGH BEND

W h e n e v e r possible, conductors should be routed on a single metal layer through bend and fold areas to enhance fl exibility. When not

Figure 5-30 It is preferred practice to route traces through bend areas in a single metal layer. If two metal layers are required, the traces should be off set or staggered.

possible, the conductor should be staggered from side to side to avoid the I-beam eff ect discussed earlier.

DESIGN TO KEEP COPPER IN NEUTRAL AXIS

Th e concept of neutral axis is very important to fl exible circuits. In theory, the center of any item being bent is nearly immobile, with stress being absorbed by the outer layers of material. Th erefore, if the copper (or other metal) foil is kept to the center of the design, the fl exing life should be enhanced. (See Figure 5-31.)

Many experiments have verifi ed this theory. Data provided in the graph in Figure 5-32 dramatically illustrate the eff ect that neutral axis placement can have on the fl exing life of a fl ex circuit.

FLEX DYNAMIC AREAS WITH THE COPPER GRAIN DIRECTION

Th e orientation of the grain of the copper foil has a defi nite eff ect on fl exural life of a design. Grain direction is of greatest importance with fl ex circuit designs fabricated using rolled and annealed (RA) or traditional

Figure 5-31 By keeping copper in neutral axis, it is possible to minimize cyclic strain and vastly extend fl ex endurance.

electro-deposited (ED) copper foil. With vendor-electroplated copper on sputtered fi lm, orientation is not as critical, as there is no specifi c grain direction. Th e eff ects of grain direction on fl exural life can be very signifi cant, as the data found in the graph in Figure 5-32 indicate.

FLEX CIRCUIT CONSTRUCTION AND COPPER GRAIN DIRECTION EFFECTS ON FLEXURAL ENDURANCE

unbalanced

2 semi-balanced

B balanced

Figure 5-32 Data show construction infl uence on fl exural endurance.

NOTES:

1. The unbalanced construction consisted of 25µm polyimide with 25µm adhesive on a base of 50µm polyimide with 25µm adhesive and oneounce copper.
1. The semi-balanced construction used adhesive to achieve the desired balance (25µm polyimide with 50µm adhesive). The base was the same as above.
1. The balanced construction had a coverlay makeup that matched the base material exactly (50µm polyimide with 25µm adhesive).

KEEP FLEXURAL ARC SMALL

For maximum fl ex life, it is best to keep the range of the fl exural arc or total angle of fl exure of the circuit for dynamic designs as small as possible (that is, fl ex the circuit over the smallest possible distance). Th is is a key technique used in later-model disk drive applications to allow them to achieve their present high-fl ex-life cycling.

PROVIDE THE LARGEST BEND RADIUS POSSIBLE

Th e designer is advised always to provide the largest practical radius through bend areas. Th is design approach is especially important for dynamic fl ex, but, as has been previously noted, it can also be

important in fl ex applications that are apparently static in nature.

Th e graphic and simple equation in Figure 5-34 illustrate the eff ect of bend-radius diameter on the copper foil. As can be concluded by calculation, the elongation requirements for the copper foil rise signifi cantly as

Figure 5-34 Small-diameter bend radii demand greater elongation from materials used in fl ex circuit construction, especially copper foil.

bend radii decrease.

GUIDELINES FOR MINIMUM BEND RADII

While fi nite element modeling can provide excellent predictive data for suggesting bend limits, there are some common guidelines that have long served to keep the design inside the limits. For normal bending of fl exible circuits, those guidelines can be found in Table 5-5. For very high fl ex life dynamic fl ex circuit designs, fabrication and testing of prototypes commonly remains the preferred method of design verifi cation.

Table 5-5 Minimum bend radii design guidelines for fl ex circuits

| Flex CircuitType | MinimumBendRadius | |-----------------------------------------------------|-------------------------------------------------------------------| | Single Metal Layer | 3-6 x circuit thickness | | Double-sided Flex | 6-10x circuit thickness | | Multilayer Flex | 10-15x circuit thickness (or more) | | Dynamic Application (Only single-sided recommended) | 20-40x circuit thickness (increase in bend radius increases life) |

CREASING AND FOLDING FLEX CIRCUITS

Creasing and hard folding of fl ex, while not a preferred practice, can be successfully accomplished with some attention to certain details. When required, circuit should be bonded to prevent it from bending back at the crease or fold line. Strain relief is also recommended. As noted earlier, it is important to keep the construction balanced for best fl exural endurance life. Th e ideal copper for such strain-bending applications will be a low strength, high-elongation copper. Fully annealed soft copper is normally a good choice for applications requiring a small radius bend.

BENDING FLEX CIRCUITS TO HOLD SHAPE

When bending fl ex circuit products for static, form-to-fi t applications, holding shape is a desirable condition. However, fl ex circuits sometimes have some elastic memory. Th e following principles for shaping fl exible

circuits to fi t permanently in their application will help to overcome the condition. Th e fi rst principle is maximizing the metal area. Copper, or any other metal one might use for the conductors, will permanently deform plastically when bent beyond its elastic limit.

Many polymers (elastomers are generally excluded, although they can take a set over time) will also permanently deform if their elastic limit is exceeded; their limit, however, is many times greater than that of metal. Th us, when the composite structure that we now call a fl ex circuit is bent, the metal has plastically deformed, while the polymer is still likely to be in its elastic range.

PROVIDE FOR METAL DOMINANCE IN BEND AREA

In order for the copper (or other metal) to prevent the polymer from snapping back, it must overwhelm the elastic memory of the polymer. Copper is stronger and higher in elastic modulus, but if the traces are small or the copper is a low percentage of the local area, the remnant elastic strain in the polymer may cause the fl ex circuit to regress to its original fl at shape. Th is method is in keeping with the practices used by fl exible circuit manufacturers to help maintain dimensional stability.

Figure 5-35 Very small bends in the fl ex circuit are possible, as demonstrated in this fi gure (from a disc drive application).

WIDENED CIRCUIT TRACES THROUGH BENDING ZONE

If circuit weight is a concern, the area of extra copper can be localized. In such cases, the circuit features are widened in the area of the bend and then reduced in width again as they enter and exit (see Figure 5-36). Circuit traces should taper to the new width in both directions.

DETERMINING BEND AREA LENGTH

As to the potential question, Th rough what length of the bend area should the traces be widened? A simple method to get a fi rst order approximation is to determine the circumference of an imaginary circle having the desired bend radius, and multiply that result by the bend angle divided by 360 (the degrees in a circle). Th is should ensure that a suffi cient

amount of the bend area is fi lled with the wider copper traces. However, a little extra length may be required, depending on the construction.

USE THICKER COPPER IN BEND AREA

If widening the traces alone does not help suffi ciently, then one of two analogous methods can be used. One can either use a thicker metal foil or use a thinner fl exible base material. Th e objective remains the same: Make certain that the metal can overwhelm the polymer in order to hold the fi nal shape. Th ere are advantages and disadvantages to both paths. Making the copper thicker may make etching a bit more diffi cult; it will also take longer to etch and will use more chemistry. On the other hand, making the polymer thinner could make handling a bit more diffi cult, and the strength of the fi nal assembly will not be as great as with the alternative method.

PERMANENT SHAPING ALTERNATIVES

Slight over-driving of the bend to create a stable, more permanent shape can be used to advantage, with the caveat that the minimum bend radius for the fl ex construction not be violated. Note that when permanently bent and plastically deformed, the copper is normally thinned in the area of the bend, and is thus weakened. If a truly accurate predictive solution is desired, one can use fi nite element modeling methods.

HEAT FORMING

Another way to get the fl ex circuit to hold shape is to form it (usually using a mandrel of some sort), bend the circuit into shape, and then apply heat to the fi xture, allowing it to cool in place. Th e objective is to relieve all of the remnant elastic strain in the polymer by allowing it to deform plastically to the fi nal shape with the addition of heat. Th is approach works easiest with polymers and/or adhesives that have relatively low melting points. It is a very common method for making dome switches in polymer thick fi lm circuits using polyester base materials.

In contrast, polyimide has a very high melting temperature, making it a less attractive candidate. In this method, one must normally rely on the ability to get above the glass transition temperature of the adhesive and allow the circuit to cool back below that temperature before releasing it from the mandrel.

USE OF LOW-MODULUS POLYMERS

A fi nal choice for permanent shaping is to use nontraditional base materials. Th ese would be materials of low strength and having little if any elastic strength. Unreinforced FEP or PTFE [Tefl on], for example, falls into this category. Th is combination will allow the user to deform the circuit permanently into the desired shape. Th ere are other options that are variations on one or more of these themes, but these are the basics.

Summarizing this topic, keeping and holding fl ex circuits in shape is not that diffi cult, but it does take some attention. Th e method of choice relative to those mentioned above will, obviously, depend on the demands of the design and its application.

FINITE ELEMENT MODELING OF FLEX

Over the years, with increases in computing power and increased availability of memory, there has been a signifi cant improvement in fi nite element modeling tools, in terms of both cost and performance. Th us, it is not surprising that-given the importance of the mechanical requirements to the long-term performance of a fl exible circuit assembly-many companies are beginning to perform fi nite-element modeling of the circuits to validate the design before committing the product to manufacture. Th is can be much more cost eff ective than iterating through a number of prototype runs, provided the modeling parameters are properly selected.

FEA tools are widely available and many can accept data directly from many types of design soft ware and the user need only input

Figure 5-37 Finite element modeling can signifi cantly improve the chances of fi rst-pass success in design for application by providing valuable information about the location and magnitude

material properties. Meshing is automatic. Figures 5-37 and 5-38 illus- trate where the strain is located and dislocation in a simple bend and also reemphasize the importance of coverlayer in reducing strain on the copper foil.

SHIELDING FLEX CIRCUITS

With the proliferation of wirelessly operated electronic products, there is increasing concern around the world about electromagnetic interference or EMI. Shielding of fl ex circuits may be required to block out unwanted electronic inter-

Figure 5-38 Finite element modeling illustrating stress in a threemetal-layer fl ex circuit during bending. Note buckling of material in bend area in lower image. (FEA models courtesy Michael Perry)

ference or noise. Th ere is, in addition, the converse need to minimize emissions emanating from the circuit as well. Shielding can be accomplished by using the electronic system in a shielded room, but this obviously is not practical for most of today's electronics. Alternative methods, therefore, are necessary.

Following are some techniques developed for fl exible circuits:

INTEGRAL FOIL SHIELDS

Th e use of laminated copper (or other metal) foil on the outer surfaces of the circuit can provide excellent shielding. Such approaches should be carefully weighed to assess their cost-eff ectiveness, however. If only simple shielding is required, lower-cost screened-on coating may serve. All metal foils also tend to be stiff er and heavier than the alternatives.

THIN METAL SHIELDING

Vacuum sputtering of metal, and other dry metallization processes such as vapor deposition, have been used successfully to metallize the outer surface of the circuit, providing the required shielding. Such shielding is very lightweight and has been successfully employed in satellite applications. Th e process requires the use of expensive equipment and may not be suitable for cost-sensitive applications.

SCREEN-PRINTED CONDUCTIVE POLYMER SHIELDING

Screen-printing the surface with conductive polymers is a technique that has been used with great success in many applications. To use this technique, access to ground must be provided through the coverlayer. Th is allows the conductive ink to be screen-printed down into the opening and make contact. No openings are required when a fl oating ground is satisfactory for the application. (See ground plane section.)

GRAPHITE COATINGS

Depending on the level of signal attenuation sought or required by the application, lower-conductivity coatings such as graphite or carbon fi lms may also serve the user's needs. Graphite coatings can be easily applied by spraying.

MEMBRANE SWITCHES

Membrane switches are ubiquitous. Any time one physically interfaces with the world of electronics, the odds are that he is doing so through a membrane switch of some type. As common as they are, membrane switches are also perhaps one of the more unsung and least visible members of the fl ex circuit family. As switches are fundamental elements of the electronic interconnection hierarchy, it is worthwhile to look more deeply into this important component.

Basically, a membrane switch is-as its name implies-an electrical switch created on a thin fi lm or membrane. Th ey are typically of low power, with maximum current ratings of around one-tenth of an amp. Th e circuitry for these devices is oft en somewhat elaborate since they frequently provide connections for a host of diff erent input functions. Perhaps the most common application for membrane switches is in a keyboard of some type. While not all keyboards are made of fl exible materials, a great many are. Th e most common layouts are matrix type (rows and columns) and common line connections (a common trace plus some number of switches). Other structures are possible depending on the needs of the user, such as integration of electronic circuits (including passive devices such as resistors) and land patterns for component mounting.

CONDUCTOR MATERIALS FOR MEMBRANE SWITCHES

Th e conductor material used for membrane switches varies by application. Copper and polymer thick fi lm (PTF) inks are the most common choices. Cost is usually a key factor when making the choice. Because of this, a substantial number of membrane switches have screenprinted PTF conductors consisting of metal-fi lled ink. Obviously, the typically lower conductivity of printed inks limits the conductivity, but they

are not normally meant to carry current. Rather, they are designed to send a simple signal pulse. Copper is employed when there is need to solder devices to the membrane or when higher conductivity is needed; however, conductive adhesives have proven quite acceptable in most applications.

Th e switch-life of a membrane contact can vary signifi cantly, from several thousand to many millions. Th e life-determining factors include such matters as materials of construction, contact design, switch travel, and operating conditions, among many others.

TACTILE FEEDBACK

While some membrane switches do not provide for tactile feedback, which some suppliers call a Type 1 structure, it is arguable that one of the key elements of membrane-switch design involves providing for tactile feedback. Th is is commonly a small snap or click that can be felt when a switch is pressed and released. Determining the right amount of force to be applied (the actuation pressure) is both an art and a science. Some customers are very adamant about 'feel, ' which, unfortunately, can be subjective.

Th ere are basically two approaches to getting tactile feedback: polymer dome contacts (sometimes called a Type 2 structure) and metal dome contacts (sometimes referred to as a Type 3 structure). Metal-dome tactile switches have spring metal dome over the contact area. When pressed, it snaps down to complete a circuit and snaps back when released. Th e shape and thickness of the metal (commonly spring stainless steel) will determine actuation force. Th ey off er a long life but are not well suited for use with fl ex circuits.

In contrast, polymer dome switches are embossed into the plastic fi lm overlaying the circuit. It is possible to get a good tactile feel from such contact, and though their life expectation is heavily infl uenced by their use environment, they can endure millions of cycles if designed right. Furthermore, they have the advantage when it comes to cost, since they reduce the number of parts-thus reduced assembly time and complexity. Of course, one can opt to not use tactile feedback. To this end, an auditory response method is employed, such as a small beep. Because of their extreme simplicity, these tend to be the lowest-cost contacts of all.

CONTACT DESIGN

Th e contact area design is another important and interesting element of a membrane switch. Contact fi nish can vary. Gold, nickel, silver and even graphite have been used. Th e layout will vary with the type of contact used. For example, for a shorting contact, interdigitated fi ngers are oft en used. However, when a metal dome contact is employed, a central contact with a surrounding ring is frequently seen (Figure 5-39). Much time and

eff ort has been expended over the years to defi ne the ideal contact.

Figure 5-39 Basic membrane-switch contact designs are shown without an overlayer. The shorting contact on the right normally is attached to a resilient material that holds it off the surface when it is not pressed down.

CONNECTING TO MEMBRANE SWITCHES

Perhaps the element most recognizable as a fl ex circuit in a membrane switch is the tail element. commonly made to serve as half of a mated pair connector. In such constructions, graphite is commonly applied over the circuits as the contact fi nish. In such cases, the circuit traces are simply plugged into a ZIF-type connector of a sort described earlier in this chapter.

Th is brief review of membrane switches is by no means complete. It serves only as an introduction to the technology and was meant to provide some appreciation for this important use of fl ex circuit technology.

CONTROLLED-IMPEDANCE CONSTRUCTIONS

Controlled-impedance electronic signal-transmission cable applications are one of the applications best suited to the capabilities of fl exible circuits. Because of the rapid increase in the growth of high-speed, high-performance electronic products, the use of controlled-impedance interconnections is expected to grow. Following are some of the construction types available using fl ex circuits. Figure 5-40 shows examples of each type.

COPLANAR STRIPLINE

In this very simple method of creating a controlled impedance cable, the circuit is produced with one metal layer by alternating ground and power. Such constructions are well suited to higher-characteristic impedance designs. A drawback of these designs is that they are susceptible to EMI noise.

MICROSTRIP CIRCUITS

Microstrip circuit designs are two-layer fl ex constructions, of which one metal layer is devoted to ground. Such circuits have been successfully employed in transmission line applications, are normally targeted for a 50Ω characteristic impedance, and are oft en used for single-ended

interconnections. Higher-characteristic impedance designs can be built, but fl exibility usually suff ers.

STRIPLINE CIRCUITS

Stripline circuits and transmission line cables are also excellent applications for fl ex circuits. With ground layers on both sides, great signal integrity can be achieved. However, such constructions tend not to be very fl exible due to the extra dielectric and metal foil used. Stripline circuits are oft en designed to 100 ohms and are frequently used for diff erential pair interconnections.

360° SHIELDED STRIPLINE

360° shielded stripline constructions attempt to replicate coaxial cable constructions by virtue of the fact that the signal line is surrounded on four sides by ground. Such applications are of interest where crosstalk is a concern and where maximum signal integrity

Figure 5-40 Various controlled-impedance constructions

is required. Like stripline fl exible circuit, these constructions tend to be rather stiff .

PSEUDO COAXIAL CABLE

Some researchers have taken 360° stripline constructions a bit further and used either plated through holes at points along the length of the fl ex circuit or plated trenches along the length of the copper ground to improve the shielding between the signal lines.

CAD TOOLS

Designing fl exible circuits is, clearly, no mean task. Th ere are many special design elements that must be attended to in order for a design to move easily through the manufacturing process. One important family of enabling technologies can be found in computer-aided design (CAD) tools. Newer CAD solutions are being adapted specially to meet the needs of fl exible circuit designers.

In fact, with the increasing emphasis on the use of fl exible circuits in all manner of electronic products, CAD tool suppliers, such as Mentor Graphics, are creating new tools to address the growing need for rapid learning in this important technology sector.

Th ese new tools not

Figure 5-41 Example of a screen shot for a fl ex circuit design executed using CAD software developed for fl exible circuits (Photo courtesy Mentor Graphics)

only help to make certain that the appropriate connections are made but also now address the various mechanical needs for curved trace routes to prevent stress risers. An example of a computer aided fl ex circuit design having one such solution applied can be seen in Figure 5-41.

SUMMARY

Th is chapter has provided an overview of some basic, yet very important, design practices required for successful implementation of fl ex circuit technology. As stated earlier, there are many other design requirements for PCBs in general, many of which are common to both fl ex and rigid circuit designs. Many concerns of fl ex circuits are created by the mechanical demands placed upon them. Th e reason is simple: What was formerly a simple replacement for a standard PCB has become a much more complex and highly mechanical, multifunctional interconnection device.

Th is simple reality forces the electronics designer to give proper consideration to mechanical concerns that could normally be ignored in rigid board design, but which are vital in the designing of fl ex circuits.

Metadata

SourceLBL Practical Flex Circuit Design Guidelines

Tokens21,871

Chunks103

Chunks (103)

#0207 tokens

## INTRODUCTION Flexible circuits are obviously unique among electronic packaging technologies in that they off er a wide variety of advantages unobtainable using conventional rigid interconn...

#1231 tokens

## DESIGN PRELIMINARIES Before embarking on a fl ex circuit design, it is important that a holistic overview of the project be taken. In this overview, a circuit designer should attempt t...

#2141 tokens

## USE OF MOCKUPS Let us reassert here the value of using paper doll mockups. Th is simple practice will help the designer prevent many errors by exposing potential problems early and will save both...

#3278 tokens

## DESIGN WITH A BIAS FOR COPPER Favoring the use of copper in design is good practice for some very solid reasons, assuming that there are not important confl icts created by the practice. If all o...

#4590 tokens

## In general, it is recommended that the largest practical tolerance be given Proper application of tolerances of fl ex circuit design features is a matter that concerns both the fl ex circuit man...

#5329 tokens

## GENERAL GUIDELINES FOR DIMENSIONING AND TOLERANCING Proper dimensioning and tolerancing of fl ex circuits is vital to achieving good manufacturing yield. While it is not possible to poin...

#684 tokens

## SPECIAL DESIGN CONSIDERATIONS Th ere are some unique elements of fl ex circuit design that require early consideration. Mostly they address mechanical issues that could aff ect usability...

#7405 tokens

## LAY OUT CIRCUIT TO CONSERVE MATERIAL Conservation of material in fl exible circuit manufacture serves to help keep manufacturing costs down. Th is is important because fl exible circuit material...

#8175 tokens

## SERVICE LOOPS Th e addition of a small amount of length to the fl ex circuit beyond the design requirement is advisable for most fl ex circuit applications. Th is little extra length of materia...

#997 tokens

## STAGGERED LENGTH CIRCUITS (BOOKBINDER CONSTRUCTION) For ease of fl exing multilayer and rigid fl ex designs, the use of staggered length design is commonly employed. Th e technique is accomplish...

#101223 tokens

## CONDUCTOR SIZING AND ROUTING In general, fl ex circuit conductor width and thickness are determined by a combination of current carrying requirements, the voltage drop allowance and/or c...

#11366 tokens

## Trace Width Minimums Th e minimum practical trace width for a fl ex circuit varies from vendor to vendor. Flex circuits with traces 250µm (0.010") and greater are fairly easy to obtain; however, ...

#12186 tokens

## CONTROLLED IMPEDANCE LINES Controlled impedance transmission cabling is a popular application for fl ex circuits, and the value of such product is increasing as digital data signaling speeds cont...

#13184 tokens

## ETCH FACTORS An etch factor is a tool used by the manufacturer to compensate for isotropic etching process eff ects. It is recommended that the designer check with the vendor to determin...

#14463 tokens

## CONDUCTOR ROUTING CONCERNS Th ere are a few general issues related to conductor routing of a fl ex circuit. Th e fi rst item of concern is keeping to a minimum the number of crossovers in the la...

#15113 tokens

## Flexible Circuit Technology Figure 5-9 I-Beamed vs. Staggered Conductors. I-beamed constructions increase the stiff ness of the circuit through bend and fold areas. A better alternative, if space...

#16238 tokens

## GROUND PLANE DESIGN Ground areas should be crosshatched if electrical consideration of the design will allow for such. Th e practice helps both to reduce weight and improve circuit fl exibility. ...

#17257 tokens

## POLYMER THICK FILM DESIGN GUIDELINES Due to their unique nature, polymer thick fi lm (PTF) circuits have their own very specifi c design rules. As a screen printing based technology, the limits ...

#1871 tokens

## CONDUCTOR WIDTH AND SPACING FOR PTF Generally, minimum conductor width and spacing is considered to be in the range of 375µm (0.015"). It is possible to produce fi ner lines and spaces using PT...

#19119 tokens

## CURRENT CARRYING CAPACITY OF PTF Silver-based polymer thick fi lm inks, under normal conditions, can be expected to carry approximately 25% of the current of copper circuits for equivale...

#2099 tokens

## SCREEN-PRINTED PTF RESISTORS Screen-printed resistors are fairly commonly incorporated into PTF circuit designs. If used in a design, the resistors should be kept to a minimum of one or two values...

#21111 tokens

## TERMINATION DESIGN CONCERNS FOR PTF CIRCUITS Th e design rules for circuit pads or lands for PTF circuits are similar to those used for rigid printed wiring boards; however, the terminat...

#2262 tokens

## INTERCONNECTION DESIGN FEATURES Th is chapter section deals with interconnection design features, including both through holes and lands for making interconnections and the design criteria ...

#23412 tokens

## HOLE SIZES FOR COMPONENT LEADS While surface mount technology has become the dominant interconnection technology for electronic component assembly, through hole components are still used in many a...

#24285 tokens

## VIA HOLE SIZING Vias can be designed as small as is practical for the manufacturer's yield. Small vias off er great advantage for circuit layout, but circuit cost may be aff ected if they are...

#25139 tokens

## FILLETING OF LANDS AND PADS Termination lands and pads on fl exible circuits should be fi lleted. Th is process increases pad area and helps to distribute stresses local to t...

#26349 tokens

## PAD OR LAND HOLD DOWNS FOR SINGLE-SIDED FLEX Termination pads on single conductor layer circuits and surface mount lands on fl ex circuits of any layer count may require special land ...

#27653 tokens

## SURFACE MOUNTING LANDS FOR FLEX Surface mount in combination with fl ex circuit technology is now very popular as the world's fl ex circuit designers look to the success of ...

#28209 tokens

## LANDS FOR PLATED THROUGH HOLES Except for the shared need for fi lleting, double-sided fl ex with plated through holes does not require tie-downs, due to the rivet eff ect from the plated throu...

#29337 tokens

## BUTTON PLATING An alternative plated through hole construction can be created using a process called button plating. Th e process can best be characterized as one where through holes and vias are ...

#3074 tokens

## COVERLAYER AND COVERCOAT CONCERNS As mentioned earlier in the section on fl ex circuit materials, there are several types of fl exible covercoating systems available. Each has...

#3185 tokens

## Adhesive-backed fi lms Adhesive-backed polymer fi lms are the type of coverlayer most frequently specifi ed and used by fl ex circuit designers and manufacturers. It is also the fl ex...

#3263 tokens

## Screen-printable liquid covercoats Applied and cured by simple means, screen-printable liquid covercoats are the least expensive covercoat type and the one most oft en used with polymer thick fi ...

#33409 tokens

## Photoimageable liquid and fi lm polymers Newer methods for covercoating fl ex circuits involve the use of photoimageable polymers. Th e results have been very promising. In process...

#34103 tokens

## SIZING COVERLAYER OPENINGS As was seen in the discussions on surface mount land design, the sizing of coverlayer openings varies according to pad design features and with the number of metal laye...

#35406 tokens

## TRACE-TO-CUT LINE CONCERNS Best current practice for fl ex circuit design generally recommends that the edge of the part to the edge of conductor spacing be >1.25mm (0.050"). It has been shown...

#36125 tokens

## TEAR-RESISTANCE FEATURES IN FLEX DESIGN All fl ex circuit designs should be made as tear-resistant as possible. While the material may not be intrinsically tear-resistant, tear-resistan...

#3781 tokens

## Radius All Internal Corners Th e fi rst line of defense against tearing is to make certain that all internal corners are provided with as generous a radius as possible. Th i...

#3880 tokens

## Leave Metal in Corners Th e circuit design should, if possible, have small areas of copper provided for at internal corners to serve as tear stops at the inside of corner radii. Th is se...

#39120 tokens

## Laminate Glass Fabric in Corners Glass cloths can be laminated into corners during the fabrication process. Th ough not fl exible, this method has been shown to provide a very robust ...

#40119 tokens

## Use Fluoropolymer Coverlayer Th e use of fl uoroplastics such as Tefl on ® as coverlayers helps to improve tear resistance by virtue of the high tear resistance of the polymer itself. Th is is d...

#4170 tokens

## Use of Radiused Slots Th e use of slots with ends that have a radius to access relieved circuit features also can serve to provide tear resistance. Normally, such features can easily be p...

#4293 tokens

## Drilled Holes at Corners or Ends of Slits Drilled or punched holes in corners or at the ends of access slits have been used with success when fl exible appendages must be spaced close together. T...

#43335 tokens

## Aramid Fibers Inside Cut Line As an alternative to glass cloth, the use of aramid fi bers routed through corners or along the entire outline of the fl ex circuit is a unique method to stop teari...

#44410 tokens

## STIFFENERS AND REINFORCEMENTS FOR FLEX Stiff eners or reinforcements are commonly used to support components Figure 5-19 Example of circuit with embedded glass-cloth tear restraint on fl e...

#45100 tokens

## SPECIAL TECHNIQUES FOR STIFFENERS Special design techniques allow stiff eners to serve more than the function of component support. For example, while the primary purpose is to support c...

#46117 tokens

## ROUT-AND-RETAIN STIFFENERS Rout-and-retain stiff eners are produced by CNC routing of the substrate so as to leave it attached in certain locations for easy removal later. Such constructi...

#47106 tokens

## RETURN TO WEB PUNCHING Return to web punching (also referred to as 'punch out, punch in') of the stiff ener requires special punch tooling wherein the rigid material is punched out of the panel a...

#48220 tokens

## SCORING OR DICING OF STIFFENERS If features of the fl ex circuit design allow the use of scoring or dicing tools to prepare the stiff ener panel is potentially possible. With respect to the scor...

#49144 tokens

## ADHESIVES FOR BONDING OF STIFFENERS All of the bonding adhesives used in the creation of fl ex circuit laminates are candidates for attaching a fl ex circuit to a stiff ener. Th e choice of whi...

#50228 tokens

## PRESSURE-SENSITIVE ADHESIVES Pressure-sensitive adhesives are very commonly used to attach stiff eners. Th ey are perhaps the most versatile and easiest to use. Th ey exhibit ver...

#5193 tokens

## THERMOSETTING ADHESIVE FILMS Th ermosetting adhesive bonding fi lms (cast-acrylic fi lms or fl ex circuit bondplies) can also be used to bond fl ex circuits to stiff eners, but they re...

#52113 tokens

## LIQUID ADHESIVES One and two part liquid epoxy type adhesives have been used for bonding stiff eners to fl ex circuits. Th ey are diffi cult to apply uniformly and thus do n...

#53136 tokens

## THERMOPLASTIC ADHESIVE FILMS Th e use of thermoplastic-based adhesive fi lms for bonding fl ex circuits to stiff eners is another common option. Th ermoplastic fi lms have some unique ...

#54110 tokens

## UV CURABLE ADHESIVES Ultraviolet curable adhesives are another potential adhesive choice for stiff ener attachment. With some screen-printable formulations, the UV 'activates' the p...

#5577 tokens

## HOLES FOR STIFFENERS Th e diameter and relative sizing of mounting holes for components, of the circuit or breaking of the copper at the transition point can more easily occur if the procedure is...

#56129 tokens

## ROUNDED STIFFENER EDGES AT TRANSITION Th e stiff ener edges in areas where the fl ex circuit egresses from the perimeter of the stiff ener should be rounded or provided with a radius...

#57117 tokens

## FILLET TRANSITION EDGE OF STIFFENER Filleting of the transition edge of a stiff ener with a resilient adhesive or epoxy is another common method of strain relieving circuits. Th e small bead of a...

#58217 tokens

## STRAIN RELIEF FOR UNSUPPORTED FLEX CIRCUITS Strain relief should also be provided when mounting the fi nished circuit or assembly. Th e following methods can be used for this purpose: -...

#59256 tokens

## COMPONENT HOLES IN STIFFENER Holes in the stiff ener for through hole mounting of electronic components, such as dual in-line packages (DIPS), should be 250µm375µm (0.010-0.015...

#60110 tokens

## ASSEMBLY MOUNTING HOLES Holes in the stiff ener for mounting the assembly should be equal to or slightly smaller in diameter than the holes in the fl ex. Th is assures that the stresses are plac...

#6187 tokens

## UNSUPPORTED MOUNTING HOLES Mounting holes that are not supported by a stiff ener should be designed to maintain copper around the hole for added strength. (See Figure 5-22.) Th is practice is of ...

#62349 tokens

## METHODS OF CONNECTING FLEX CIRCUITS Th e provision of strain relief at the edges of stiff eners helps to prevent stress risers from occurring at transition areas from fl ex to rigid. Tearing C...

#631012 tokens

## FLEXIBLE CIRCUIT CONNECTOR TYPES Some basic connectors are relatively simple devices. Examples include insulation displacement and crimp-type connectors. Th ese have proven popular in appli...

#64423 tokens

## BENDING AND FLEXING DESIGN CONCERNS Figure 5-28 Making fl ex circuit connections directly between chip packages can provide signifi cant performance improvements. (Courtesy SiliconPipe, San Jose...

#65102 tokens

## BENDING AND FLEXING TECHNIQUES A number of clever approaches and techniques have been developed by engineers over the years to achieve the desired bending or fl exing motion in a fl exible circu...

#66120 tokens

## AVOID PLACEMENT OF THROUGH HOLES IN BEND AREAS An important design practice that is sometimes overlooked or ignored is the avoidance of placing plated through holes in the bend areas. Th is is ...

#67122 tokens

## ROUTE TRACES AT 90° THROUGH BEND AND FOLD AREAS Conductor traces should be routed through bending and fl exing areas at 90° (perpendicular) to the bend line. Th is is an intuitively natural routi...

#68123 tokens

## ROUTE CONDUCTORS ON A SINGLE LAYER THROUGH BEND W h e n e v e r possible, conductors should be routed on a single metal layer through bend and fold areas to enhance fl exibility. When no...

#69148 tokens

## DESIGN TO KEEP COPPER IN NEUTRAL AXIS Th e concept of neutral axis is very important to fl exible circuits. In theory, the center of any item being bent is nearly immobile, with stress being ab...

#70187 tokens

## FLEX DYNAMIC AREAS WITH THE COPPER GRAIN DIRECTION Th e orientation of the grain of the copper foil has a defi nite eff ect on fl exural life of a design. Grain direction is of greatest importa...

#71140 tokens

## NOTES: no 0 unbalanced 2 semi-balanced B balanced Figure 5-32 Data show construction infl uence on fl exural endurance. - 1) The unbalanced construction consisted of 25µm polyimide with 2...

#72101 tokens

## KEEP FLEXURAL ARC SMALL For maximum fl ex life, it is best to keep the range of the fl exural arc or total angle of fl exure of the circuit for dynamic designs as small as possible (tha...

#73180 tokens

## PROVIDE THE LARGEST BEND RADIUS POSSIBLE Th e designer is advised always to provide the largest practical radius through bend areas. Th is design approach is especially important for dynamic fl e...

#74326 tokens

## GUIDELINES FOR MINIMUM BEND RADII While fi nite element modeling can provide excellent predictive data for suggesting bend limits, there are some common guidelines that have long served t...

#75158 tokens

## CREASING AND FOLDING FLEX CIRCUITS Creasing and hard folding of fl ex, while not a preferred practice, can be successfully accomplished with some attention to certain details. When required, circ...

#76236 tokens

## BENDING FLEX CIRCUITS TO HOLD SHAPE When bending fl ex circuit products for static, form-to-fi t applications, holding shape is a desirable condition. However, fl ex circuits sometimes have som...

#77177 tokens

## PROVIDE FOR METAL DOMINANCE IN BEND AREA In order for the copper (or other metal) to prevent the polymer from snapping back, it must overwhelm the elastic memory of the polymer. Copper ...

#7884 tokens

## WIDENED CIRCUIT TRACES THROUGH BENDING ZONE If circuit weight is a concern, the area of extra copper can be localized. In such cases, the circuit features are widened in the area of the bend and t...

#79142 tokens

## DETERMINING BEND AREA LENGTH As to the potential question, Th rough what length of the bend area should the traces be widened? A simple method to get a fi rst order approximation is t...

#80182 tokens

## USE THICKER COPPER IN BEND AREA If widening the traces alone does not help suffi ciently, then one of two analogous methods can be used. One can either use a thicker metal foil or use ...

#81115 tokens

## PERMANENT SHAPING ALTERNATIVES Slight over-driving of the bend to create a stable, more permanent shape can be used to advantage, with the caveat that the minimum bend radius for the fl ex constr...

#82233 tokens

## HEAT FORMING Another way to get the fl ex circuit to hold shape is to form it (usually using a mandrel of some sort), bend the circuit into shape, and then apply heat to the fi xture, allowing i...

#83190 tokens

## USE OF LOW-MODULUS POLYMERS A fi nal choice for permanent shaping is to use nontraditional base materials. Th ese would be materials of low strength and having little if any ...

#84322 tokens

## FINITE ELEMENT MODELING OF FLEX Over the years, with increases in computing power and increased availability of memory, there has been a signifi cant improvement in fi nite element mode...

#85218 tokens

## SHIELDING FLEX CIRCUITS With the proliferation of wirelessly operated electronic products, there is increasing concern around the world about electromagnetic interference or EMI. Shielding o...

#8699 tokens

## INTEGRAL FOIL SHIELDS Th e use of laminated copper (or other metal) foil on the outer surfaces of the circuit can provide excellent shielding. Such approaches should be carefully weighed to assess...

#87115 tokens

## THIN METAL SHIELDING Vacuum sputtering of metal, and other dry metallization processes such as vapor deposition, have been used successfully to metallize the outer surface of t...

#88122 tokens

## SCREEN-PRINTED CONDUCTIVE POLYMER SHIELDING Screen-printing the surface with conductive polymers is a technique that has been used with great success in many applications. To use this ...

#8964 tokens

## GRAPHITE COATINGS Depending on the level of signal attenuation sought or required by the application, lower-conductivity coatings such as graphite or carbon fi lms may also serve the user's needs...

#90346 tokens

## MEMBRANE SWITCHES Membrane switches are ubiquitous. Any time one physically interfaces with the world of electronics, the odds are that he is doing so through a membrane switch of some type. As co...

#91266 tokens

## CONDUCTOR MATERIALS FOR MEMBRANE SWITCHES Th e conductor material used for membrane switches varies by application. Copper and polymer thick fi lm (PTF) inks are the most common...

#92455 tokens

## TACTILE FEEDBACK While some membrane switches do not provide for tactile feedback, which some suppliers call a Type 1 structure, it is arguable that one of the key elements of membrane-switch ...

#93193 tokens

## CONTACT DESIGN Th e contact area design is another important and interesting element of a membrane switch. Contact fi nish can vary. Gold, nickel, silver and even graphite have been used....

#94162 tokens

## CONNECTING TO MEMBRANE SWITCHES Perhaps the element most recognizable as a fl ex circuit in a membrane switch is the tail element. commonly made to serve as half of a mated pair connector. In su...

#95121 tokens

## CONTROLLED-IMPEDANCE CONSTRUCTIONS Controlled-impedance electronic signal-transmission cable applications are one of the applications best suited to the capabilities of fl exible circuits. Be...

#9682 tokens

## COPLANAR STRIPLINE In this very simple method of creating a controlled impedance cable, the circuit is produced with one metal layer by alternating ground and power. Such constructions are well...

#97111 tokens

## MICROSTRIP CIRCUITS Microstrip circuit designs are two-layer fl ex constructions, of which one metal layer is devoted to ground. Such circuits have been successfully employed in transmission l...

#98112 tokens

## STRIPLINE CIRCUITS Stripline circuits and transmission line cables are also excellent applications for fl ex circuits. With ground layers on both sides, great signal integrity can be ach...

#99118 tokens

## 360° SHIELDED STRIPLINE 360° shielded stripline constructions attempt to replicate coaxial cable constructions by virtue of the fact that the signal line is surrounded on four sides by ground. ...

#10073 tokens

## PSEUDO COAXIAL CABLE Some researchers have taken 360° stripline constructions a bit further and used either plated through holes at points along the length of the fl ex circuit or plated trenches...

#101296 tokens

## CAD TOOLS Designing fl exible circuits is, clearly, no mean task. Th ere are many special design elements that must be attended to in order for a design to move easily through the ma...

#102208 tokens

## SUMMARY Th is chapter has provided an overview of some basic, yet very important, design practices required for successful implementation of fl ex circuit technology. As stated earlier...